CMC

Bauman Bag ( Hoist )

Rainy Day Equipment Bauman Bag
The Bauman Bag provides a single-point suspension for lifting a patient during a hoist
or short-haul evacuation. The Hoist model has adjustable length straps
allowing the bag to be configured to your aircraft. The fixed length
straps on the Short Haul model position the bag at the best aerodynamic
angle for flight stability. Both bags can be used with backboards or
litters. Less than 13 lb (6 kg), the Bauman Bag stores in an 11 x 21
inch (28 x 53 cm) stuff bag, reducing weight and storage space on the
aircraft. The bag includes reflective tape and a pocket for a chemical
light sticks for low light and night operations. Both bags can be used
with backboards or litters. Less than 13 lbs. (6 kg), the Bauman Bag
stores in an 11 in. by 21 in. (28 x 53 cm) item # 728001 Product Weight 2
lb 15 oz (5.9 kg) Model Hoist Color Red

This product has now been discontinued and replaced with the CMC Helitack range

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C728001		Bauman Bag ( Hoist )	Stock Level: Out of Stock	POA			Add to Favourites

Bauman Screamer Suit

Rainy Day Equipment
Bauman Screamer Suit Rainy Day Equipment
Designed for rapid extrication by hoist or short haul, the Screamer Suit dons
quickly without the delay of putting on a full body harness designed for
a rescuer. The Screamer Suit is easy to put on and holds the subject
securely during lifting. The system adjusts from small patients to large
patients up to 500 lb (227 kg). Not intended for a patient with a
spinal injury or other injury requiring a litter evacuation.item #
728101Product Weight 4 lb 9 oz (2.1 kg)Color Red

This product is no longer produced and has been replaced with the CMC Helitack range

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C728101		Bauman Screamer Suit	Stock Level: Out of Stock	POA			Add to Favourites

Bearer Tie In 34" 7mm Cord

The Bearer Tie-In, also known as, the Foot-End Spider, is used in sets of 2 and they attach from the
foot-end of the litter to the foot-end, set-of-fours, or haul point. These cords are set up as purcells to
allow for adjustment on steep angle evacuations. 7 mm x 34" sewn in a bound loop.
MBS kN 17

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
CP34		Bearer Tie In 34" 7mm Cord	Stock Level: In Stock Special Order	RRP: $55.00	Quantity:		Add to Favourites

ClimbTech Removable Bolt Anchor 1/2"

One of ClimbTech’s most popular removable bolt anchors, this portable
concrete anchorage connector can be used in a variety of fall
protection applications.
Size: 1/2″
Breaking Strength: 2,700 lbf / 12 kn
Weight: .2 lb (90 g)
Compliance: ANSI Z359.7 & CE-EN 795

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C391050		ClimbTech Removable Bolt Anchor 1/2"	Stock Level: Pre-order Special Order	RRP: $157.00	Quantity:		Add to Favourites

CMC Rope Bags

Solid performers for years, our popular Rope Bags have been enhanced with innovative features for even greater convenience and ease of use.
New contoured backpack-style shoulder straps were redesigned to offer greater comfort when carrying heavy loads.
Bag tops incorporate a rugged rip-stop nylon for easy closure. Grab handles secured inside the top can be used to hold the bag
open for quicker stuffing or to carry the bag from the top, haul-bag style. A sturdy side carry handle has been relocated for improved
balance and includes gear loop attachments. The bottom of the bag features our new reach-in pouch that enables easy access so that even a
knotted rope end can be deployed from either side, while remaining secure when transporting. Sewn web loops are attached at the base to
enable tying the rope end off internally or externally.
Reach-in bottom allows bag to be used easily from both ends
Contoured backpack-style shoulder straps with integrated handle
Clear-view sleeve for rope I.D. / log information
Side carry handle allows for easy loading/unloading from apparatus
Exterior gear loops for attaching carabiners
Constructed from extra long-life 1,000-denier CORDURA® nylon
Made in USA
Weight 226 g
Volume 11 L
Dimensions (L x D) 41 x 20 cm
Rope Capacity: 12.5 mm 30 m
Rope Capacity: 11 mm 38 m

Code	Product Name	Stock Level	Price	Quantity	Wishlist
C430102	CMC #1 Ropebag Blue	Stock Level: Pre-order Special Order	RRP: $120.00	Quantity:	Add to Favourites
C430103	CMC #1 Ropebag Red	Stock Level: Pre-order Special Order	RRP: $120.00	Quantity:	Add to Favourites
C430203	CMC #2 Ropebag Red	Stock Level: Pre-order Special Order	RRP: $217.00	Quantity:	Add to Favourites
C430205	CMC #2 Ropebag Black	Stock Level: In Stock Special Order	RRP: $217.00	Quantity:	Add to Favourites
C430301	CMC #3 Ropebag Orange	Stock Level: Pre-order Special Order	RRP: $215.00	Quantity:	Add to Favourites
C430303	CMC #3 Ropebag Red	Stock Level: Pre-order Special Order	RRP: $215.00	Quantity:	Add to Favourites
C430401	CMC #4 Ropebag Orange	Stock Level: Pre-order Special Order	RRP: $237.00	Quantity:	Add to Favourites
C430402	CMC #4 Ropebag Blue	Stock Level: Pre-order Special Order	RRP: $237.00	Quantity:	Add to Favourites
C430403	CMC #4 Ropebag Red	Stock Level: In Stock Special Order	RRP: $237.00	Quantity:	Add to Favourites
C430601	CMC #6 Ropebag Orange	Stock Level: Pre-order Special Order	RRP: $277.00	Quantity:	Add to Favourites
C430603	CMC #6 Ropebag Red	Stock Level: In Stock Special Order	RRP: $277.00	Quantity:	Add to Favourites

CMC 1.5" PMP S/S Swivel Pulley

Our new Prusik-minding pulley (PMP) is ideal for high anchor points
or tripod use. The rotating swivel aligns the rope with the direction of
the pull. Its stainless steel sheave can be used with either rescue
rope or wire cable. By combining the swivel with the pulley, overall
system length is minimized, increasing travel. The patented pivoting
side plate allows the rope to be quickly inserted.
• Stainless steel sheave allows use with wire cable
• Prusik-minding side plate opens without having to disconnect the pulley from the anchor
• A double-detent button prevents accidental opening of side plate
• Sealed ball bearings provide maximum efficiency
PRODUCT WEIGHT 11.3 OZ (320 G)
TYPE SINGLE SHEAVE TREAD SIZE 1-1/2 X 1/2 IN (38 X 13 MM)
SHEAVE STAINLESS STEEL
COLOR BRONZE / SLATE
NFPA RATING GENERAL USE
3 SIGMA MBS 43 KN

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C300430		CMC 1.5" PMP S/S Swivel Pulley	Stock Level: In Stock Special Order	RRP: $330.00	Quantity:		Add to Favourites

CMC 1.5" Single Swivel Pulley

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C300431		CMC 1.5" Single Swivel Pulley	Stock Level: In Stock Special Order	RRP: $270.00	Quantity:		Add to Favourites

CMC Anchor Strap Large 213cm

Anchor straps have a tough job, and see a lot of wear and tear. Over the years, we’ve learned that cuts and abrasion are the greatest threats
to their safety and service life. To dramatically increase both, our Anchor Straps now feature two layers of the same durable mil-spec,
resin-coated nylon web. Sewn by our highly skilled workers who make our rescue harnesses, our Anchor Straps feature forged steel D-rings
individually proof loaded and sized for easy choker (girth-hitch) configuration when desired. Sewn-on web keeper allows for improved
organization when stowed. Use our sized Anchor Strap Sleeves for added edge and abrasion protection.Note: We recommend using a Delta
Quick Link connector (part #382121) to prevent possible tri-axial loading of a carabiner when used in a basket configuration.
Strength Specifications for All Sizes:
Basket (U) Configuration:85 kN (19,108 lbf)
End-to-End Configuration: 46 kN (10,341 lbf)
Choker Configuration: 48 kN (10,790 lbf)
Product Weight 1.5 lb (680 g)
Length 7 ft (213 cm) Color Blue
NFPA Rating General Use

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C201024		CMC Anchor Strap Large 213cm	Stock Level: Pre-order Special Order	RRP: $132.00	Quantity:		Add to Favourites

CMC Arizona Vortex Kit

Named for its origin in the rugged Red Rock highlands of northern Arizona, the Arizona Vortex Kit is a unique multipod that was created
from years of experimental development. The Vortex represents the pinnacle of at-the-edge frames, which no standard multipod can match
today. The recently improved Vortex Bag System allows a single rope technician to carry the entire Vortex Kit using our RigTech Pack™ and 2 redesigned Leg Bags.

The originator of modern artificial high directionals (AHD)s, the Vortex is a tripod, bipod and monopod in one all-inclusive kit. Its precision
machined two-piece head can be rigged as a standard tripod or, in advanced applications, as an A-frame, Sideways A-frame, Gin Pole or a
multitude of other configurations. The tripod can be formed into an Easel A-frame with adjustable leg lengths. The versatile third leg
allows rescuers to set up an artificial high directional in virtually any urban, industrial or wilderness application. When configured in the
A-frame and Easel A-Frame applications, pulleys can be attached directly into the Head Set using the included quick-pins rather than carabiners,
retaining valuable headspace and working clearance. The Vortex is ideal for use with high lines and tracking line offsets. The extra attachment
points also work well for rope access where several lines may be needed over the edge. Sets for both the Raptor Feet and Flat Feet
are included to provide secure footing options on varying terrain and industrial surfaces. The Flat Feet now come with an improved rubber pad
that can be easily replaced when needed.

Kit Components
The Arizona Vortex Kit comes complete with:
2-Piece Head Set
Head Set Pulley Wheel
Head Pins (4)
Inner Legs (3)
Outer Legs (7)
Leg/Foot Pins (17)
Flat (Omni) Feet (3)
Raptor (Claw) Feet (3)
Orange Pin Flags (21)
Adjustable Hobble Straps (3)
8mm Tether Cord (40ft)
User Manual
Vortex Bag System
RigTech Pack™
Leg Bags with Shoulder Straps (2)
Foot Set Sleeves (2)
Pin Storage Bag

Specifications
Min Height: 2.7 m (9 ft)
Max Height (with additional legs): 3.7 m (12 ft)
Weight (with both foot sets): 33 kg (72 lb)
Shipping Weight (including all parts, bags and packaging): 43 kg (95 lb)
Certification: Classified to NFPA 1983 (2017 ED) – General Use
MBS: 36 kN (8,093 lbf)

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C727300		CMC Arizona Vortex Kit	Stock Level: Pre-order Special Order	POA			Add to Favourites

CMC Ascender

The CMC Ascender rope grab utilizes a spring-loaded cam to facilitate progression on life safety rope. Widely used by rescue teams
as a rope clamp for an attachment to a litter harness tender line, as a travel restrict rope grab, ascending rope, and other applications where a
mechanical rope grab provides greater efficiency.
Compact, lightweight rope grab
Machined from aircraft-grade aluminum alloy for superior strength
Spring-loaded cam produces instant progress capture
Removable pin releases cam, facilitates easy installation at any point on rope
Large connection point in cam accommodates rescue-sized carabiners
Stainless steel quick-release pin
Designed for optimal rope strength
Made in USA
Weight 8.8 OZ (252 G)
Dimensions 4.5 L x 3 H x 1 W
Color Red / Gray
NFPA Rating
7/16 1/2 in (11-13 mm) TECHNICAL USE;
1/2 in (12.5 -13 mm) GENERAL USE

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C341103		CMC Ascender	Stock Level: In Stock Special Order	RRP: $259.00	Quantity:		Add to Favourites

CMC Atom Rescue Harness

The ATOM™ Series, our most comfortable harness line ever developed, is the culmination of stripping harness design down to the basics and
re-imagining a performance-enhancing tool for rescue and rope access. CMC has incorporated years of feedback from experts who spend long hours
in a harness. In addition, the ATOM harness went through rigorous field testing, resulting in a harness design that improves safety,
comfort and workflow efficiency in all the ways you can’t see, but feel.Every detail in the ATOM Rescue Harness has been thoughtfully designed for
the rescue professional. From the structure and attachment points to buckles, gear and accessory loops and other features, the ATOM delivers
maximum comfort, safety and workflow efficiency in a lightweight and low profile harness system.Improved architecture molds to the user for a lightweight, low-profile fit.
Ergonomic design for maximum comfort and support:Padding constructed from dual density foam, laminated to optimize load
distribution and apply the right amount of support only where needed.Waist and leg pads are constructed with rolled edges to provide additional comfort.Y-back construction and bridged front lift:Allows for optimal adjustment at each shoulder.Provides a secure fit while minimizing pressure from the harness at the neck.Constructed with polyester webbing:Keeps a supple hand for comfort and easy buckle adjustment.Water repellent and UV resistant material for lasting strength and durability in extreme weather conditions.Gear
loop over-braid is based on a 32-carrier polyester, rope sheath design that delivers a familiar texture and functional robustness.Multiple accessory attachment points provide ample space for stowing and organizing hardware and tools.
UL Certified to relevant ANSI Z359.11, CSA and NFPA 1983 (2017 ED) standards. Made in the USA of domestic and foreign components.
Core Features
Red webbing at the shoulders and the front leg drop provide higher visibility.
Steel attachment points at the waist, sternal and dorsal position offer robust and low profile connection points.
Cobra Quick-Connect Buckles at the legs and the right shoulder make donning quick and efficient.
One-piece shoulder pad:Reduces harness twisting for easy donning.Bridges dorsal webbing for improved comfort at the neck.
Flexible gear loops offer a low profile gear stowage solution especially when working in confined spaces.
Workseat attachment points located at the waist to connect the CMC Skysaddle.

Product Weight 2.7 kg (5.95 lb)
Waist Size 66-81 cm (26-32 in)
Color Red / Black
NFPA Rating CLASS III

Code	Product Name	Stock Level	Price	Quantity	Wishlist
C202122	CMC Atom Rescue Harness Small	Stock Level: Pre-order Special Order	RRP: $1,140.00	Quantity:	Add to Favourites
C202124	CMC Atom Rescue Harness Medium	Stock Level: In Stock Special Order	RRP: $1,140.00	Quantity:	Add to Favourites
C202125	CMC Atom Rescue Harness Large	Stock Level: Pre-order Special Order	RRP: $1,140.00	Quantity:	Add to Favourites

CMC AZ Bound Loop Prusik

Years of development, testing and fine tuning has made our Prusik cord a
preferred choice by rescue schools, agencies and rescuers alike. Our
sewn Prusiks offer unmatched performance—with strength equivalent to a
tied Prusik loop, just without the cumbersome knot. The factory-sewn
SecureStitchTM is covered with durable clear shrink tubing
that allows regular inspection and helps protect the stitching for
longer life. Some rescuers prefer a bound-loop style Prusik for cinching
the attachment bight around the carabiner to help snug the Prusik to
the connector. Our AZ Bound-Loop Prusiks are identical to our Sewn Loop
Prusiks except that the shrink tube captures both sides of the loop
while allowing adjustment.
Length 18 in (46 cm)
Color Red
MBS 20 kN (4,496 lbf)

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C293383		CMC AZ Bound Loop Prusik 46cm	Stock Level: In Stock Special Order	RRP: $44.00	Quantity:		Add to Favourites
C293386		CMC AZ Bound Loop Prusik 63cm	Stock Level: In Stock Special Order	RRP: $44.00	Quantity:		Add to Favourites

CMC Azorp Kit ( Arizona Omni Rigging Pod)

The newest companion to the Arizona Vortex Kit, the AZORP (Arizona Omni Rigging Pod) allows even greater versatility.
This two-in-one rigging pod is a welcome addition to the Vortex lineup and combines the versatility of having two component halves that can be
used in combination, or separately, at different positions on the inner or outer Vortex legs. Machined from one solid block of T-6 aluminum, it
delivers superior strength with a sleek and simple design without using welds. The inner and outer AZORP pods can also be used together as a
two-flange rigging pod in combination with a Vortex leg compression member.The AZORP Storage Bag features a quick-draw closure and an
external carabiner loop. The main compartment has a separate sewn-in pocket to hold the AZORP quick pins. Constructed of tough,
water-resistant 1,000-denier Cordura® nylon.
AZORP Kit contains:
1 – AZORP Outer Pod (blue)
1 – AZORP Inner Pod (orange)
2 – Stainless Steel Quick Pins
1 – AZORP Storage Bag

Product Weight (Kit) 3.4 lb (1.6 kg)
Dimensions (each pod) 6-3/8 x 4 in (16 x 10 cm)
Color Orange / Blue
NFPA Rating General Use
3 Sigma MBS 65 kN

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C727400		CMC Azorp Kit ( Arizona Omni Rigging Pod)	Stock Level: Pre-order Special Order	POA			Add to Favourites

CMC Aztek 8mm Cord 50ft Sewn Eye

The working line for the AZTEK system must be strong, perform well with
small diameter Prusik cord, and be supple enough to pack compactly.
Constructed of 100% nylon, our design-specific AZTEK ProSeries Cord
blends high strength with abrasion resistance for proven performance.
The sheath construction is engineered for compatibility with our 6 mm
sewn Prusiks and ease of packing into the AZTEK ProSeries Pack. Bright
orange for high visibility.
Designed for use with the AZTEK System. 50 feet of 8 mm AZTEK ProSeries
Cord with a sewn-eye termination on one end to fit the AZTEK pulley
becket.
12kN 8mm Orange

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C293421		CMC Aztek 8mm Cord 50ft Sewn Eye	Stock Level: Pre-order Special Order	RRP: $226.00	Quantity:		Add to Favourites

CMC Aztek Bound Loop Prusik 6mm Blue

Years of development, testing and fine tuning has made our sewn Prusiks,
Purcells and cord a preferred choice by rescue schools, agencies and
rescuers everywhere. Our 100% nylon sewn products offer unmatched
performance—with strength equivalent to a tied Prusik loop, just without
the cumbersome knot. Our factory-sewn SecureStitch™ is covered with
durable clear shrink tubing that allows for regular inspection and helps
protect the stitching for longer life. These bound-loop Prusiks and
Purcell were designed specifically for use with our AZTEK ProSeries®
System.
13kN 106cm/42 in
Blue

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C295012		CMC Aztek Bound Loop Prusik 6mm Blue	Stock Level: Pre-order Special Order	RRP: $54.60	Quantity:		Add to Favourites

CMC Aztek Bound Loop Prusik

Years of development, testing and fine tuning has made our sewn Prusiks,
Purcells and cord a preferred choice by rescue schools, agencies and
rescuers everywhere. Our 100% nylon sewn products offer unmatched
performance—with strength equivalent to a tied Prusik loop, just without
the cumbersome knot. Our factory-sewn SecureStitch™ is covered with
durable clear shrink tubing that allows for regular inspection and helps
protect the stitching for longer life. These bound-loop Prusiks and
Purcell were designed specifically for use with our AZTEK ProSeries®
System.
13kN 22.8cm Orange

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C295001		CMC Aztek Bound Loop Prusik 6mm Orange	Stock Level: Pre-order Special Order	RRP: $31.00	Quantity:		Add to Favourites
C295002		CMC Aztek Purcell Prusik 6mm Blue	Stock Level: Pre-order Special Order	RRP: $31.00	Quantity:		Add to Favourites

CMC Aztek Omni Pulley

The AZTEK OMNI pulley blocks and sheaves are machined from solid
aluminum, feature swivel connection points, and utilize high-efficiency
bearings. These pulleys were developed in the early 2000’s by Reed
Thorne of Sedona based Ropes That Rescue. The AZTEK system has
become a valuable multipurpose tool of rescue and technical rope access
practitioners. The AZTEK pulleys are offered individually or included in
our AZTEK ProSeries System
Note: The Slate blue pulley includes the AZTEK quick release pin and the Orange pulley comes with the side becket cover and screw.
Orange
226g
Sheave 26mm x10mm
NFPA Technical Use
43kN

Code	Product Name	Stock Level	Price	Quantity	Wishlist
C300320	CMC Aztek Replacement Quick Release Pin	Stock Level: Pre-order Special Order	RRP: $54.00	Quantity:	Add to Favourites
C300321	CMC Aztek Omni Pulley Orange	Stock Level: Pre-order Special Order	RRP: $276.00	Quantity:	Add to Favourites
C300322	CMC Aztek Omni Pulley Slate Blue	Stock Level: Pre-order Special Order	RRP: $276.00	Quantity:	Add to Favourites

CMC Aztek Proseries System

As one of the most versatile tools in rope rescue, the CMC AZTEK ProSeries System reflects our philosophy of keeping rigging equipment
simple, efficient, light, compact, and multi-purpose. Originally developed by Reed Thorne of Arizona-based Ropes That Rescue, the
AZTEK (Arizona Technician’s Edge Kit) is used worldwide and offers more than 100 rigging solutions in a single bag. The CMC AZTEK ProSeries
System is made in USA of US and foreign components.This system now includes an updated AZTEK ProSeries Pack
that has improved fabric durability, new reflective piping, and a fresh OD Green color. The pack is feature rich with 1000D nylon/Tarpaulin
construction for abrasion resistance, mesh panel for ventilation and drying, Garage Pockets™ to protect cord, double-zippered top
compartments, and tension lock buckles for carrying on the waist or thigh.

Everything comes pre-rigged and fully assembled for immediate deployment.The set-of-fours includes 15.2 m (50 ft) of 8 mm AZTEK ProSeries Cord,
which is CMC’s high-performance 100% nylon blend. These can extend to 3.6 m (12 ft) while providing a 4:1 or 5:1 mechanical advantage with a
Minimum Breaking Strength (MBS) of 38 kN (8,542 lbf).For a personal edge travel-restrict with nearly 15.2 m (50 ft) of adjustable
travel, attach the carabiner of the personal end of the system to an appropriate anchor and restrict edge travel using the integrated Purcell
connected to your harness. The sleeved web edge-pro helps protect the cord around anchors with abrasive surfaces.

The CMC AZTEK ProSeries System comes fully assembled in the AZTEK ProSeries Pack and includes the following:
CMC AZTEK Omni Pulley Set, (one blue, one orange) – UL Classified to NFPA 1983 (2017 ED)
Quick Pin for AZTEK Omni Pulley
AZTEK ProSeries Cord – 15.2 m (50 ft) of 8 mm hi-viz orange, 15 kN (3,372 lbf), Sewn-Eye Termination – 12 kN (2,698 lbf)
AZTEK Edge-Pro Tubular Webbing, blue .6 m (24 in)
ProTech™ Aluminum Auto-Lock Carabiner w/ removable keeper pin – 29 kN (6,519 lbf)
AZTEK Bound-Loop Prusik, orange (6 mm) – 9 in
AZTEK Bound-Loop Prusik, blue (6 mm) – 9 in
AZTEK Bound-Loop Purcell, blue (6 mm) – 42 in
Maillon Rapide Quick Link, Oval (7 mm) – 27 kN (6,070 lbf)

Weight 4.3 lb (2 kg)
NFPA Rating General Use
3 Sigma MBS 38 kN (8,542 lbf)

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C500104		CMC Aztek Proseries System	Stock Level: In Stock Special Order	RRP: $1,160.00	Quantity:		Add to Favourites

CMC Boost Foot Loop

The BOOST is a highly adjustable foot loop developed for rope access operations and rescue techniques. It is strong, compact, and easy to use, making it a versatile tool for moving on rope, hauling loads, and performing pick-offs.

BOOST features low profile webbing, smooth adjuster buckles, and an easy one-handed foot closure system. Adjustable from 92 - 144 CM, BOOST can be optimally sized to fit the technician and their current task. The length is controlled by a custom-designed buckle that balances high holding strength with ease of adjustability. At the base of the foot loop is a durable and collapsible stiffener that assists with foot entry and exit. The elastic foot closure system can be tightened or loosened with one hand. It stays in place when working on rope, aiding, or walking on the ground.

BOOST is built with dedicated rescue functionality. Each component is selected for its high strength to withstand the forces generated during pick-offs. The BOOST’s large adjustment range supports a variety of suspended rescue techniques and raising systems. The length can be quickly increased using the custom adjuster buckle, allowing for rapid transitions from ascent to rescue. Low friction Dyneema webbing provides a high degree of efficiency in M/A systems, which is especially useful in combination with carabiners or other hardware. The webbing is also pulley-compatible and its compact size enables clean operations and quick stowage.
Features:

Highly adjustable, compact foot loop with dedicated rescue functionality.
Smooth custom aluminum buckle adjusts length from 92 - 144 CM.
Low friction, high strength Dyneema webbing facilitates rescue pick-offs.
Easy one-handed closure system securely fastens to footwear.
Durable and collapsible foot loop stiffener assists with entry and exit.
Adjustable and removable keeper tightens web around carabiners.
Pulley-compatible for building efficient mechanical advantage systems.
Lightweight and low profile for clean operations and quick stowage.
71g

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C201196		CMC Boost Foot Loop	Stock Level: Out of Stock	RRP: $120.00	Unavailable for Online Purchase		Add to Favourites

CMC Capto

CAPTO is an intuitive device that combines a multi-functional rope grab, high-efficiency pulley, and
integrated becket for easy hauling and ascending. Built around an innovative V-groove Cam,
CAPTO is designed to handle rescue loads while providing force-limiting overload protection.
FEATURES
• Combines a rope grab, pulley, and becket in a compact device
for hauling & ascending.
• Incorporates a force-limiting V-groove Cam designed to provide
overload protection.
• Installs quickly on tensioned and un-tensioned lines, no need for
knots or hitches.
• Opens one-handed and gives simultaneous access to
components for rapid rigging.
• Builds efficient M/A systems and smoothly progresses from a
3:1 to a 5:1 M/A.
• Releases and resets easily, even after high loading, making it
ideal for rescues.
• Travels down rope in vertical systems, resetting and maximizing
the haul field.
• Allows installation of an accessory loop for remote resets and
device stowage.
• Provides an integrated becket for M/A components, lanyards,
and foot loops.
• Replaces multiple devices in one, streamlining training and
operations.
336011
10.5 - 11 mm (7/16 in) Rope
508 g
150 x 70 x 31 mm
36 kN pulley
Certifications
• NFPA 2500 (1983) General Use; Rope Grab
• NFPA 2500 (1983) General Use; Pulley
• EN 12841:2006/B; 200 kg
• EN 567:2013
• EN 12278:2007; 36 kN (18+18)

Code	Product Name	Stock Level	Price	Quantity	Wishlist
C293005	CMC Capto Soft Shackle	Stock Level: Out of Stock	RRP: $17.00	Unavailable for Online Purchase	Add to Favourites
C336011	CMC Capto 11mm	Stock Level: Pre-order Special Order	RRP: $939.00	Quantity:	Add to Favourites
C336013	CMC Capto 13mm	Stock Level: Pre-order Special Order	RRP: $939.00	Quantity:	Add to Favourites

CMC Clutch

More is Possible
Introducing the all-new CLUTCH, the latest evolution in rescue and rope access hardware that enables the technical rope professional to do more with
less. This multi-purpose device was designed and engineered in collaboration by two companies with a collective 90 year history in rope
management under heavy loads: CMC, a company with roots in rescue and rope access, and Harken Industrial, a manufacturing company with roots
in high performance sailing.
Designed for intuitive, efficient operation, ease of use and optimal control, the versatile CLUTCH is suited to a multitude of rigging operations:
Single wearable tool suited for efficient hauling, controlled lowering, smooth personal descent, easy ascending and belaying.
Stainless steel ratcheting and rotating sheave provides efficient and audible progress capture.
Rope loading/unloading is secured with an innovative double-latched side plate design that is independent of the device‘s attachment point.
Anti-Panic brake and force limiting features ensure operational safety and overload protection.
Machined aluminum chassis clad with stainless steel wear guards ensures lightweight durability.
Integrated becket allows for direct connection of mechanical advantage systems.
The only 10.5-11 mm rope diameter compatible device certified to NFPA 1983 (G-Rated), ANSI Z359.4 and EN 12841/C, 341/2A, and 15151/8.
The CLUTCH and CMC’s G11™ Lifeline can be used together to build NFPA G rated systems using 11 mm rope, saving space and reducing weight.
Patented and Made in the USA
ROPE SIZE 10.5 – 11 MM (7/16 IN)
WEIGHT 836 G (1.84 LBS)
DIMENSIONS 208 X 112 X 47 MM (8.2 X 4.4 X 1.9 IN)
MAX LOAD 272 KG (600 LBS)
3-SIGMA MBS PULLEY 40 KN (8,992 LBF) / BECKET 22 KN (4496 LBF)
CERTIFICATIONS NFPA 1983 (2017 ED) GENERAL USE; ANSI/ASSE Z359.4-2013; EN 12841: 2006/C; EN 341: 2011/2A; EN 15151-1: 2012/8

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C335011		CMC Clutch 11mm	Stock Level: Pre-order Special Order	RRP: $1,549.00	Quantity:		Add to Favourites
C335013		CMC Clutch 13mm	Stock Level: Pre-order Special Order	RRP: $1,555.95	Quantity:		Add to Favourites

CMC Cobra D Uniform Rappel Belt

Designed for Emergency Rappel
In a class by itself, CMC offers the only Uniform Rappel Belt certified to
NFPA standards. Designed for everyday wear but with the performance
needed for an emergency rappel or belay. Standard uniform wear for fire
fighters, search and rescue, and SWAT personnel, the belt is constructed
to the same exacting standards as our harness line and is the only certified
uniform belt available. The belt uses 1-3/4” web that fastens securely
without requiring any hook-and-loop material. The AustriAlpin D-ring
COBRA® buckle is manufactured from 7075 aluminum alloy and
features a built-in stainless steel D-ring (Buckle:18 kN / 4,000 lbf
MBS, D-ring: 22 kN / 5,000 lbf MBS, straight pull). The buckle requires a
two finger release and will not open when loaded. Included web keeper
secures excess web at tail end of belt. Adjustable, one size fits most.
66-122cm waist
294g
Black

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C202400		CMC Cobra D Uniform Rappel Belt	Stock Level: Pre-order Special Order	RRP: $198.00	Quantity:		Add to Favourites

CMC CSR2 Pulleys

The design of our redesigned CSR2 (Confined Space Rescue) Pulley is stronger yet lighter and incorporates 7/16 in (11 mm) to 1/2
in (13 mm) life safety rope. Ideal for industrial applications as well as many rescue operations, the CSR2 uses our proprietary,
patented locking system, which eliminates a toothed cam or Prusik so it can be easily and safely released while under load. (The absence of the
toothed cam means that even if the system is fully collapsed and pulled tight, it can still be released easily. Systems using a toothed cam must
be raised even further before the cam can be released, which can be impossible if the system is fully collapsed without thinking about this
problem ahead of time – causing potential problems with the load on the system becoming stuck.) An integral thrust-bearing swivel reduces torque
by aligning the pulley with the load, thereby increasing efficiency and safety. Its larger size allows for the easy application of rescue-size
carabiners.
Machined from a solid block of aircraft-grade aluminum, the CSR2 features a high-strength aluminum side plate, sealed bearings and
anodized aluminum sheaves. The side becket location allows for maximum lift height and full retraction of the system, and a removable becket
cover facilitates changing out lifeline with sewn terminations.
All-new stronger, lighter-weight design
Compatible with 11-13 mm life safety rope
Meets NFPA 1983 (2017 ED) – General Use
CSR2 Pulley MBS 46 kN (10,341 lbf) / CSR2 Double Pulley MBS 45 kN (10,116 lbf)
Machined from solid block of aircraft-grade aluminum
Made in USA
Weight 1.5 lb (680 g)
Sheave Tread Size 2 1/4 x 1/2 in (57 x 13 mm)
Color Gray
NFPA Rating General Use
MBS 45 kN (10,116 lbf)

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C300342		CMC CSR2 Double Pulley	Stock Level: Pre-order Special Order	RRP: $951.00	Quantity:		Add to Favourites
C300343		CMC CSR2 Pulley	Stock Level: Pre-order Special Order	RRP: $1,730.00	Quantity:		Add to Favourites

CMC DualCom Radio Harness

Years of proven in-the-field experience and valuable customer
feedback have helped CMC develop the most advanced dual-communication
radio chest harness on the market. Ergonomically designed for all-day
comfort, our DualCom Radio Harness is constructed from tough, durable
Cordura® nylon with a soft, breathable D3 fabric backing.
This fully-featured harness is equipped for carrying a variety of
communication devices and field necessities, keeping everything you need
close at hand.
3 adjustable holsters to accommodate two variable size radios and a GPS unit or spare battery
2 side-zip pockets can accommodate a 6” x 9” notebook, large smartphone, field guide, pocket knife, compass or other instruments
A main compartment (8” x 9”) that can hold a large map, mini electronic tablet, trauma scissors, field guide, spare batteries, and more
Antenna keeper on the left shoulder strap
Internal niche pocket for dispensing flagging tape through an external grommet
Front attachment loop for pocket light
2 front pen sleeves
Made in USA of domestic and foreign components
445g

Code	Image	Product Name	Stock Level	Price	Quantity	Quote	Wishlist
C240048		CMC DualCom Radio Harness	Stock Level: Pre-order Special Order	RRP: $609.00	Quantity:		Add to Favourites

Shopping Cart

Search

Shop Now

CMC